Tips-for Road Bicycles Maintenance

First what equipment do you want A bike workstand o.. A clear bike will function better than a dirty one and is really a pleas-ure to work with. Before you begin any bike maintenance you have to clean your bike, that doesnt mean a bit of wash with a cloth, you've to clean it properly and there are certainly a few things you need to do the job, you might have to purchase some equipment, but most of it is found around the house, try underneath the sink, but dont let your wife/mother find you. First what equipment do you want A bike workstand or practical tree/washing point to hang your bike o-n. If you are concerned with shopping, you will probably desire to discover about carpet first. Old rear centre or old axle or stay. Degreaser or diesel fuel (careful diesel is not best for both hands). Heated water. Washing-up liquid. 2 containers (1 with soapy and 1 with clean water). Paint brush. Old water bottle. Bottlebrush. Comfortable scrubbing brush. 2 sponges. Fabrics. Gas. And for that additional shinny end, spray polish. The most important point to consider if you are cleaning your bike is to keep your eyes open and look for something that may require repairing later, this is how a technician on a professional group does it, but he might have 10 cycles to look after, therefore its much easier with just one. The starting point Focus on the wheels, cut the fill up the old water bottle and set some degreaser in it, you can use a spray degreaser, but you waste most of it. With the paintbrush function the degreaser into the sprockets being careful to not get too much into the bearings. Then with some warm water and washing-up liquid scrub the clean, then scrub the wheels clean of old brake stop residue, you should use a little de-greaser to assist this, but dont have it in your tires. Clean the tires clean, with delicate scrubbing brush, at this point look at the tires for any cut in-the stand that could pierce later and inspect the wheels for injury or if they're wearing thin. With a soapy sponge clean the spokes and then wash them in clean water and set them to one side to dry, not in direct sunlight. Now the rest of the bike put your bike on your bike workstand or other handy piece you are able to hold it on. Put the old hub/axle/stick in the rear end of the frame so the chain can sleep on it, then using the paintbrush and the old water-bottle with the degreaser clean the chain, the front and rear derailleur, chain rings and cranks, brakes and any metal parts, try not to get it on the seat, handlebar tape and dont get too much on the headset and bottom bracket bearings. Also utilize the degreaser and paintbrush to clean under the pipe, as youll find any sill form your feeding container will make this an extremely sticky area and the degreaser must transfer it. Now take the bottlebrush or a sponge and a bucket of soapy water and clean under the saddle, under the bottom bracket, under the brakes and under the forks, use the scrubbing brush to shift any stubborn dirt, then take a soapy sponge and clean off all of the degreaser and loose dirt. Then with a clean soapy sponge clean every part of the bike, start with the handlebars and saddle and work your way down the bike ensuring the whole bike is sparkling clean, then wash with clean water. Remember keep your eyes open for things such as worn brake blocks, gritty bearings, tight or frayed wires or any cracks or harm to the frame, if all is OK put the wheels back. What to search for when you are cleaning your bike Used brake blocks. Broken or thin rim walls. Destroyed or cut tires. Destroyed string. Destroyed or bent handlebars and stem. Twisted or broken seat. Torn or used handle bar tape. Broken or worn chain sprockets and rings. Broken or worn chain. Damage to cranks or pedals. Condition or gear and brake cables. Injury to body tubes. Loose or broken spokes. Problem of brake calipers. All bearings should run smoothly. So that your bike has become clean, dry it using a clean cloth and if you want it to actually sparkle, get the spray polish out, but dont get any on the brake floor or you wont be able to stop initially you get out. Next you have to oil the chain and all moving parts, brake pivot products, front and rear derailleur, pedal springs and the pivots on the brake levers, wipe away any spilt oil, check your gears and brakes work nicely, pump-up your tires and away you go on your clear and sparkling bike. Oh! And remember to put right back all that stuff from underneath the sink before you continue your bicycle ride or youll be making your personal dinner when you get home.CarpetFirst 78 York Street London W1H 1DP 020 8099 8444

Methods For Road Bicycles Maintenance